When a wedding DJ decides to take on the task of ceremony sound, a completely different door opens up in their career. That mobile DJ may decide only to worry about offering basic playback of music, some may capture sound with a single simple handheld microphone, others may go full out and offer multiple microphones, mix in live performances, record the session, and even work in tandem or hand off their recordings to videographers. I am going to try to cover all those bases in this article.

A Speaker And A Song

For those just offering music playback this usually becomes a choice of convenience to setup and breakdown. There are numerous battery-powered speakers out there and of course regular speakers that a DJ would consider leveraging in their setup. Naturally a fully self contained speaker that can provide a wire-connected, bluetooth, or self-contained playback can be more than sufficient. Some of these speakers tend to be less expensive than a straight “cabinet” than what one would use to DJ with, so the quality may not be on the same level.

There are a ton of great speakers to consider including the Bose L1 Model II, The JBL Eon One, Maui 5 (and the 5 Go battery powered). Personally I use the Yamaha DXR8 which matches the top cabinets I use on my main system and cocktail hour. This allows me to freely swap out and circulate speakers. I personally would stay away from anything sub-$500 for this application especially if it’s battery powered. I’ve owned a couple of these units and while they are passable just a couple hundred dollar extra investment really can make a difference.

Yamaha DXR8

Microphones Galore

There are lots of microphone options out there and applying to this to ceremonies require some additional scrutiny. I know I was always looking to keep things lightweight, simple to setup, and not costing a fortune. Some basics on microphones before we continue, you need a transmitter and a receiver of some sort. If say a mic kit has a handheld and a lav pack for that receiver you can’t run both at the same time. There is always a 1:1 relationship between transmitter and receiver.

I first started to use a 4-mic GTD 1U setup that was OK. Its low cost of entry was very pleasing for a wedding DJ starting off doing ceremonies, and right off the bat I had more than a couple events that required multiple mics. I lived with the solution for 18 months and while it got me by, and I was able to get things like lav packs and over the ear mics, I would have been better off jumping into a better solution. The quality was mediocre overall.

So what do I recommend one do? Well first steer away from anything in the 600MHz spectrum since in mid-2020 you’ll be running that illegally.  I also would steer away from the 2.4GHz spectrum devices like the Audio-Technia System 10 since you could easily be overtaken by cell phones, microwaves, wifi, and other things on that spectrum. I have heard some positive things about them, but the simple fact they operate on a crowded spectrum should give pause for anyone to consider them.

What I would say to invest in is the tried and true; Sennheiser G3 series microphone kits typically coming in at $600 and lav pack kits coming in around $650 in the A or G bands. Sometimes you can get good deals getting 2-pack kits and save a little bit of money. There are also great Shure and Audio-Technica products out there too, just make sure they fall below 608MHz in their respective bands.

If you need to go with a completely self-contained battery powered solution there is the Sennheiser ew 100-ENG that has a body pack styled receiver. If say you have to go with a battery speaker and only need one quality mic solution, this is an option to consider. A lot of videographers have utilized this with a hot-shoe adapter and put the receiver right on the camera.

I personally use 3 Sennheiser G3 receivers plus a ASA-1 antenna splitter inside a shallow SKB case which simplifies wiring since the receivers (up to 8) can be powered by the ASA-1. I can expand up to 5 in the front panel if necessary and just relocate my antennas to the rear of the case.

Power. What Power?

As a wedding ceremony DJ you may find out that the location you are at simply has no power. I have done ceremonies in the woods, on a golf corse, by a lake, and so many other places where the nearest outlet can be impossible to get to. So you have to consider what your power options are when taking on this task.

As noted above, if you are just going to play music, you can leverage the units that have batteries built into them. In general you can get an hour or two for descent use, sometimes even more. As you incorporate microphones into the mix that complicates matters. You could go with the all-battery powered Sennheiser ew 100-ENG that I noted above. Or you could invest in a battery to connect everything together.

There are a lot of batteries that are out there than can last sometimes 2 or more hours. For instance the Duracell Powerpack Pro 1300 is a good portable battery that comes in at a nice > $200 price tag. The negative of this is it’s not a pure sine-wave battery which is less than ideal for sensitive electrical equipment. I personally am using a similar battery pack from Schumacher but may switch this out for a sine-wave unit from POWEROAK.

Gotta Mix Those Channels

So if you are going to be doing more than simple song playback at a ceremony you will need a way to mix all this audio together. If you are just mixing one or in some cases two audio channels some of the battery powered speakers offers competent ways to mix that audio. If you still need to stay in the realm of self battery powered devices, the Rolls MX410 gives you an option for just that.

I made an investment in the Soundcraft Ui16 (a smaller Ui12 is available as well) which requires power, but also gives me incredible flexibility to mix at a ceremony. I can move hundreds of feet away since it’s managed via a web based interface via wifi. I can control playback of music, mix mics and add effects, I can plug in a live band to the board and manage and capture their sound. The Soundcraft Ui16 has become an indispensable tool in my arsenal and also have a second unit and use it for my reception rig.

Displaying Your Gear

When I converted over to this modular setup for my ceremonies I decided to keep the system really low to the ground to keep it a bit more on the stealthy side. Since I no longer have to be directly next to my equipment it allows me to place things almost anywhere it can fit.

The ceremony setup trying to be as compact as possible

The ceremony setup trying to be as compact and stealthy as possible

Summary

There are many options to consider but the biggest one is going to be the level of service you provide for ceremony services. Do you want to just push a few songs? How about capturing a single microphone? Multiple microphones? What do you do without power? I hope the quick summary above guides you to some decisions to offer a great service to your clients.

Request For Information

user iconspacer
 
user iconspacer
 
email iconspacer
 
phone iconspacer
 
spacerphone iconspacer 
 
event iconspacer
talk iconspacer
 
 
 

 

×
Shares